1.9.10 with OS 10.11.4: ripping doesn't work anymore

The place to discuss Mac OS X version of MakeMKV
Post Reply
Kewler
Posts: 7
Joined: Thu Jun 20, 2013 3:15 pm

1.9.10 with OS 10.11.4: ripping doesn't work anymore

Post by Kewler »

I tried to rip a BD and I got a error message. So, to test if everything was OK, I tried ripping another BD that I successfully ripped a few years ago with the same BD drive and even that one didn't work anymore...

OS X 10.11.4, MakeMKV 1.9.10

Error message for the BD that was ripped a few years ago:

Code: Select all

MakeMKV v1.9.10 darwin(x86-release) started
Optical drive "BD-RE Optiarc BD RW BD-5750H 1.00" opened in DASPI v1.5 mode.
Using direct disc access mode
Error 'OS error - (ipc/send) invalid destination port' occurred while reading '/AACS/ContentHash000.tbl' at offset '0'
Failed to load content hash table, unable to verify integrity of M2TS files.
Failed to get BD disc information, reporting double-layer BD-ROM to BD+ code
Error 'OS error - (ipc/send) invalid destination port' occurred while reading '/BDSVM/00000.svm' at offset '0'
BD+ dump directory is not accessible, BD+ dump not saved
Failed to process BD+ code, please check http://www.makemkv.com/svq/ for updated program and SVQ files
Failed to open disc
Kewler
Posts: 7
Joined: Thu Jun 20, 2013 3:15 pm

Re: 1.9.10 with OS 10.11.4: ripping doesn't work anymore

Post by Kewler »

Seems to be an OS issue: I tried with another MacBook Pro with OS 10.9.5 and it works. Permissions maybe?
Woodstock
Posts: 9912
Joined: Sun Jul 24, 2011 11:21 pm

Re: 1.9.10 with OS 10.11.4: ripping doesn't work anymore

Post by Woodstock »

Error 'OS error - (ipc/send) invalid destination port' occurred while reading '/AACS/ContentHash000.tbl' at offset '0'
The operating system is not talking to the drive properly. Usually this means the drive is considered "off line". If it were Windows I'd suggest powering down and restarting. Might work for OS X as well.
MakeMKV Frequently Asked Questions
How to aid in finding the answer to your problem: Activating Debug Logging
Kewler
Posts: 7
Joined: Thu Jun 20, 2013 3:15 pm

Re: 1.9.10 with OS 10.11.4: ripping doesn't work anymore

Post by Kewler »

Woodstock wrote:
Error 'OS error - (ipc/send) invalid destination port' occurred while reading '/AACS/ContentHash000.tbl' at offset '0'
The operating system is not talking to the drive properly. Usually this means the drive is considered "off line". If it were Windows I'd suggest powering down and restarting. Might work for OS X as well.
Yes, I did try that, made no difference. Maybe then the DASPI driver is the problem? I'll try without it tomorrow.

Thanks for the hint.
Woodstock
Posts: 9912
Joined: Sun Jul 24, 2011 11:21 pm

Re: 1.9.10 with OS 10.11.4: ripping doesn't work anymore

Post by Woodstock »

Mike posted a message a year or so back that said that DASPI should ONLY be installed if MakeMKV asked for it... It was always needed in the past, but newer versions of OS X usually worked fine without it.
MakeMKV Frequently Asked Questions
How to aid in finding the answer to your problem: Activating Debug Logging
Kewler
Posts: 7
Joined: Thu Jun 20, 2013 3:15 pm

Re: 1.9.10 with OS 10.11.4: ripping doesn't work anymore

Post by Kewler »

Woodstock wrote:Mike posted a message a year or so back that said that DASPI should ONLY be installed if MakeMKV asked for it.
Oh, you mean like this message http://www.makemkv.com/forum2/viewtopic ... 635#p28051 where Mike was telling that to... me?

In my defence, that was almost three years ago... :wink:

Thanks.
Kewler
Posts: 7
Joined: Thu Jun 20, 2013 3:15 pm

Re: 1.9.10 with OS 10.11.4: ripping doesn't work anymore

Post by Kewler »

Ripped without a hitch with DASPI removed. Thanks!
Post Reply