Dolby Vision now possible through MP4 Mux.

[Angryunibrow]

First Man:
Temp Build - Hangs on wait...
@yusesope - let me know if I can supply you anything when this hangs on wait... On the temp build.

V.0.0.2 - Processed just fine to 100% first try.

V.0.0.2 Mediainfo:

Code: Select all

Video
ID                                       : 4117 (0x1015)
Menu ID                                  : 1 (0x1)
Format                                   : HEVC
Format/Info                              : High Efficiency Video Coding
Format profile                           : Main 10@L5.1@High
HDR format                               : Dolby Vision, Version 1.0, dvhe.08.06, BL+EL+RPU / SMPTE ST 2086, HDR10 compatible
Codec ID                                 : 36
Duration                                 : 2 h 20 min
Bit rate                                 : 65.6 Mb/s
Width                                    : 3 840 pixels
Height                                   : 2 160 pixels
Display aspect ratio                     : 16:9
Frame rate                               : 23.976 (24000/1001) FPS
Color space                              : YUV
Chroma subsampling                       : 4:2:0 (Type 2)
Bit depth                                : 10 bits
Bits/(Pixel*Frame)                       : 0.330
Stream size                              : 64.6 GiB (94%)
Color range                              : Limited
Color primaries                          : BT.2020
Transfer characteristics                 : PQ
Matrix coefficients                      : BT.2020 non-constant
Mastering display color primaries        : Display P3
Mastering display luminance              : min: 0.0001 cd/m2, max: 1000 cd/m2
Maximum Content Light Level              : 1000 cd/m2
Maximum Frame-Average Light Level        : 285 cd/m2

Audio
ID                                       : 4352 (0x1100)
Menu ID                                  : 1 (0x1)
Format                                   : AC-3 MLP FBA 16-ch
Format/Info                              : Audio Coding 3 + Meridian Lossless Packing FBA with 16-channel presentation
Commercial name                          : Dolby TrueHD with Dolby Atmos
Muxing mode                              : Stream extension
Codec ID                                 : 131
Duration                                 : 2 h 20 min
Bit rate mode                            : Variable
Bit rate                                 : 448 kb/s
Maximum bit rate                         : 4 533 kb/s
Channel(s)                               : 8 channels
Channel layout                           : L R C LFE Ls Rs Lb Rb
Sampling rate                            : 48.0 kHz
Frame rate                               : 31.250 FPS (1536 SPF)
Compression mode                         : Lossy
Stream size                              : 452 MiB (1%)
Language                                 : English
Service kind                             : Complete Main
Number of dynamic objects                : 11
Bed channel count                        : 1 channel
Bed channel configuration                : LFE

Remember I use eac3to to extract all my BL & EL files, and have had zero issues.
Everyone who are having issues maybe try eac3to and see what happens.

Its been zero issues on all moves for me so far.

[Arbigator]

Remember I use eac3to to extract all my BL & EL files, and have had zero issues.
Everyone who are having issues maybe try eac3to and see what happens.

Its been zero issues on all moves for me so far.

Do you mind sharing which version of eac3to you use? and the command to extract the video streams? Sorry, but I haven't been able to figure out how to get the EL out, only the base layer is extracted. Thanks.

[yusesope]

Just tested Doctor Sleep and can confirm that new temp build works. But then I just tried A Quiet Place, and it was getting hung up at the "Wait..." message. Went back to the previous version and that went through just fine.

First Man:
Temp Build - Hangs on wait...
@yusesope - let me know if I can supply you anything when this hangs on wait... On the temp build.

Sorry!
I made a stupid mistake!

I forgot to correctly initialize the Thread which takes care of reading the two layers.

You need to add the following line of code between line 442 and line 443 (follow the instructions in THIS post).

Code: Select all

self.event.set()

Respect the tabulation (as in the image), it is fundamental.

[shawnc22]

Respect the tabulation (as in the image), it is fundamental.

Got it, that worked! (although not as fundamental as spaces )

[Angryunibrow]

I obviously do not know how to edit properly in Notepadd ++, keep getting an error.
Can you post the new file?

Thanks

[yusesope]

Can you post the new file?

HERE it is.



Please guys, also test movies with HDR10+.
If you confirm that everything is ok, I will release version 0.0.3 in the next few days.

[Angryunibrow]

Can you post the new file?

HERE it is.



Please guys, also test movies with HDR10+.
If you confirm that everything is ok, I will release version 0.0.3 in the next few days.

Thank you!

I'll test this out with some HDR10+ movies as well

[Arbigator]

@yusesope

I'm still getting this with all the Bond movies I've tried, EL analysis shoots up to 100% right away, and BL stays at 0. Any idea what's going on here?

[Angryunibrow]

@yusesope

I'm still getting this with all the Bond movies I've tried, EL analysis shoots up to 100% right away, and BL stays at 0. Any idea what's going on here?

Which movie, I can try as well.
Let me know what movie that just happened too

[Arbigator]

That was Skyfall, happened on Spectre as well. Can you tell me the command you use to extract the video streams with eac3to?

[Angryunibrow]

That was Skyfall, happened on Spectre as well. Can you tell me the command you use to extract the video streams with eac3to?

Latest version of eac3to (3.34)

eac3to \path\to\bluray\ (might need " " around the directory if you have spaces in the directory or file names)

Once you get the path, usually 1)

eac3to \path\to\bluray 1) 2:BL.hevc 3:EL.hevc

The 2 layers are usually 2 & 3 (1 is always chapters)

[Angryunibrow]

That was Skyfall, happened on Spectre as well. Can you tell me the command you use to extract the video streams with eac3to?

Skyfall worked just fine.

eac3to to demux
using temp version revision 2 of the tool. (bl_el_rpu_builder_temp_version_revision_2.py)

[shawnc22]

Just tried Godzilla with the temp version of the tool and result looks good, DV and HDR10+ both there according to mediainfo

[rosavanwinkle]

is it possible to get a step by step guide? for the people that don't know yet what to do?
so they can maybe perform some tests themselves I got a fubar amount of movies that i wish to help test...

[nasuel]

Hi,

is there any way to encode the BL File that this file is smaller and then create an single DV file with the tool of yusesope?
I tried it but EL Analysis stucks at 0% when you use an encoded BL File. When you the the original BL file it works.

Sorry for the stupid question

Regards